Really working Free Energy Device.

Creating a Free Energy Device has become a dream of many People Today. Actually , it was also a Dream of a famous Scientist  Dr. Nikola Tesla some decades ago. Many people are against the fact “Free Energy “ and they always argue that an Energy cannot be created and it is against the laws of Physics.  Dr. Nikola Tesla did so many experiments to create a Free Energy Device in a past era where no electronic components were available as these days. But because of his great dedication and enthusiasm, he succeeded in creating many Free Energy Devices and other invaluable inventions like the Alternative Energy, Alternator, and the Permanent Magnet Motor which are hardly used to fulfill our day to day activities today. He is also the Inventor of the Wireless Energy and transferring that Energy through the Waves. Today we use the Radio, Television and the Mobile Phones because of his remarkable inventions.

Today, I am going to introduce you a Really Working Free Energy Device, and it is very simple and no higher knowledge of Electronic Science is required to create it. Also it needs very less components and they are as follows.

  1. 12V DC Permanent Magnet Motor 1100 R.P.M. 1/12 h.p
  2. 12V 12A Rechargeable Motor Cycle Battery
  3. Controller  made of Copper Circle ( explained later )
  4. Fly Wheel (Mass)
  5. Energizer made  of Magnets and Coils (explained later )

As a person involved in many Free Energy Experimentation work , I realized that a Battery cannot be charged, while getting a continuous load from it. Imagine we connect a Motor to a battery and keep it running foe some hours. The Battery will get discharged and the Motor will stop. But one might think that if we connect a Generator to the Motor shaft and connect the output terminals of the Generator to the Battery then this device will run indefinitely for many days without discharging the Battery, because the Battery is being recharged by the Generator. BUT IT IS NOW DONE AND THE BATTERY WILL GET DISCHARGED AS EARLIER.

The reason for this that we are unable to charge a Battery while getting a continuous output from it. Today Electric Vehicles are very famous among people. But the disadvantage of such Electric Vehicles is that we have to charge the Drive Battery for about one hour when it gets discharged. If a Battery can be charged, while getting a continuous output from it , then we can fix four electric dynamos to the four wheels of the vehicle and charge the Drive Battery while the vehicle is running. BUT IT IS COMPLETELY IMPOSSIBLE AS A BATTERY CANNOT BE CHARGED WHILE GETTING A CONTINOUS OUTPUT FROM IT.    Otherwise the Electrical Engineers who involved in the Electric Vehicle manufacturing could use this way to self-charge the Drive Battery while running the Vehicle so that there will be no need to spend hours of time in the Battery Charging Centres. 

Famous Scientist called John Bedini from UK ultimately found a way to self-charge a Battery while getting a continuous Load from it. He did many experiments on this matter and in the year 1984 he was able to demonstrate a Really working Free Energy Device which self-charged its drive battery while running the Device. His device ran indefinitely for many days without discharging the Drive Battery he was even awarded uk patens for his invention.

This invention is not much complicated and it has only few electronic components mentioned above. Following is the Diagram for this Device and the people who have a little knowledge about the Electronic Science could create it easily. But it is really working and it has been proved by many Scientists today who replicated it successfully.

N.B. Please note that all thsese Diagrams were extracted by the John Bedini Web Site.

The Basic Diagram for the Device

As explained in the above Diagram there are very few Components in the Device and this has been proved to be a really working Free Energy Device. The basic concept of this Device is charging the Battery while not getting any load from it. Just like removing a discharged Car Battery from the Vehicle and connect it to a conventional charger for charging.

In this device this concept is fulfilled by the “Controller” made of copper ring and the copper brushers. This is similar to the “Communicator” of a conventional Permanent Magnet Motor but has some changes in the Brush system. This controller allows the Drive Motor to get connected to the Battery for some time and disconnect it in the same time intervals. If the motor shaft is not connected to the “Mass” as shown in the above Diagram then it will not run. But as the Motor shaft is connected to the Fly Wheel the speed of the Motor will be increased step by step because of the Fly Wheel as it stores some moving energy, despite the fact we supply a trigger voltage (ON-OFF)  to the Motor through the Controller.  So the Fly Wheel helps the Motor to run continuously while increasing the Speed.

The Energizer is also connected to a one Brush of the Controller and when the Motor is completely disconnected by the Controller, the Energizer is connected to the Battery and it will charge the Battery well. . This is how we fulfill the concept of this device “charging the Battery while not getting any Load from it”  . The Energizer is a device which is fixed to this Device producing DC voltage required to charge the Battery. It is made of six Neodymium Magnets and Six Generator Coils connected in serial mode. So the Controller connects the Energizer to the Battery when the Motor is disconnected from the Battery and do vice versa. This method is continued and the Battery is self-charged well, while the device running. So this Device is running indefinitely without discharging the Battery. 

The Diagram of the Controller is as follows.

You can clearly see this Controller disconnects the Motor from the Battery and connect the Battery to the Energizer and do the vice versa when the Device is running.

Pulsing system of the Device

The pulsing system plays a significant role in this Device. The time period taken to connect the Motor with the Battery and the Energizer with the Battery should be equal. This can be accomplished if you create the “Controller “ well and as shown in the above Diagrams. When you fix the three Bushes please make sure that they are fixed with 90 degree alignment between each other.

Copper Section

  Also the copper section which touches the Brushes should be less than 180 degrees.

If smooth type controller is made then the following  pulses will be shown in an oscilloscope.

However it is advisable to check the pulses by an oscilloscope when the Device is running as it is a must to have the above pulses for efficient Battery Charging.

So you have been enlightened about all vital information about this Free Energy Device , I would like to add a full circuit diagram with the Energizer which charges the Battery.

There are 6 Neodymium Magnets fixed in the Rotor all North pole facing up and also there six generator coils connected in serial.  Please add rectifiers to covert the AC voltage supplied by the Generator to DC voltage to be able to charge the Battery.

This has been proved to be many Scientists who replicated it and also by ordinary People who have a little knowledge about the Electronic Science.

I also suggest you to create this Device and this is not an Internet Scam as many well experienced Scientists approve this to be really working. The Battery is being charged by the same Device and this can be used for some Household work like lighting Bulbs , charging the Laptop Battery e.t.c . However I recommend to connect a dynamo or Alternator to the main shaft of this device and then connect the Load to it. It is much good for the Drive Battery and then the Device will run much efficiently without affecting the Battery voltage by the Load.

Please note that I will not be responsible for any damages caused by the experimental work of this Device. You must assure your Safety and Accuracy.

Best of luck to the new Replicators!!!.   

Leave a Reply

Your email address will not be published. Required fields are marked *